Home > Hard Drive > Motherboard With Ide And Sata Ports

Motherboard With Ide And Sata Ports

Contents

I tried your tool (after installing WinXP on it, which took me about 1 hour and a half) and the window read : Reported capacity : 10,005 MB Factory capacity : I have an Intel motherboard with two built in IDE controllers and two built in SATA controllers. it then would niot boot at all. Blam16-02-2009, 05:06 PMThere should be a check box you can tick when that message pops up, like "Don't launch or show system configuration utility when windows starts" Tick that, make sure http://quodsoftware.com/hard-drive/how-to-connect-sata-hard-drive-to-motherboard.html

Thank you. now the hard drive isnt recognized by the bios, will not show up under my computer when set as a slave on a different desktop and will not show up under I have replaced the CMOS battery and tried different cables aswell as formatted them. Try this - Dauer: 8:36 greatestunknown 1.326.837 Aufrufe 8:36 Install An Additional SATA Hard Drive - Dauer: 15:13 hak1985org 91.199 Aufrufe 15:13 How to: set your hard drive jumpers. - Dauer: browse this site

Motherboard With Ide And Sata Ports

Opteron 165 @ 2.6 GHz 1.475vcore MSI K8N Neo2 Platinum Zalman 7000 Cu HSF ATI X800XT PE HyperX3000 512mb x4 WD 500gb SATA WD 40gb IDE WD 250gb SATA x2 WD Your mobo sounds similiar to mine. Now i can t hear the noise anymore , but still not present.I ve got a windows 7 64 disk repair taking from an hp laptop.when I put it it shows

Was it running in that computer before? anyway thats when the surfing started until I accidently came across your site which solved the problem in the time it took me to load your program. I would rather not have to manually choose the IDE drive each time I boot. Sata Hard Drive Jumper Settings I have tried pressing F8 to get into the options to recover the machine but this does not work.

Have you tried a different power connector? How To Connect Ide Hard Drive To Sata Motherboard i reboot buy powering off and it works again. In this case, to restore the original capacity of the hard drive with the HDD Capacity Restore tool that we include in this article, you may need to remove the hard https://www.cnet.com/forums/discussions/mixing-sata-and-ide-drives-in-a-system-115142/ Popular Hard Drive Utilities Try hard drive utilities such as Seatools for Seagate drives and Western Digital Data Lifeguard for WD drives.

There are two things to keep in mind, do not overload your power supply or strange difficult problems will begin to occur and make the correct BIOS settings for your data Ide Hard Drive Jumper Settings The first one was using SATA, and it went through the BIOS and PC. The way I described is the only way it will spin up on boot in a PC, is there any software that can fix this, Thanks. Trying to make this work in a WinPE environment without any luck.

How To Connect Ide Hard Drive To Sata Motherboard

I try enter in bios but i don't see any sata configuration only ide configuration and that are on auto. https://www.pctechbytes.com/hardware/hard-drive-does-not-show-up-in-bios/ I've tried your programm but with no luck since also that recognizes only the 33GB. Motherboard With Ide And Sata Ports As far as I can tell there is no limiting jumper setting that I use (even though the drive has such features). Ide And Sata Drives In Same Computer The giveaway is that the BIOS does know how big the drive is, and displays it during the prestart.

Many thanks again PS. check my blog In this case you would need to use a zero-fill tool. September 14, 2011 Dave If this is an old hard drive it might have failed electrically-there's nothing you can do about that. Download HDD Capacity Restore Tool. Sata And Ide Hard Drives Together

Please try again now or at a later time. Acronis OS selector worked for me in the past but it's not free. When running more than one OS on multiple drives you can use this option, or if running a properly installed NT/2000/XP, you can add boot options into the boot.ini. http://quodsoftware.com/hard-drive/how-to-connect-ide-hard-drive-to-sata-motherboard.html Apparently the drives need to install something like SNMP.

October 31, 2012 James So dave, i have a problem, not in the BIOS though. How To Make Ide Boot Instead Of Sata Turned off computer, pulled the SATA cable and plugged it back in. Just my comments - good tool though.

Could not read from the selected boot disk .

The hard drive was a 250 GB and it died so I replaced it with a new hard drive which is 1 TB. Thank you so much for freely distributing this siftware. Restoring factory capacity 1. Seagate Ide Hard Drive Jumper Settings Thanks Terry

Terry on December 2, 2007 9:14 am Well, I would do exactly what the program suggests… :)

Dmitry Postrigan on December 2, 2007 6:05 pm Very excellent.

You may try to find a software that does SCSI formatting or use your SCSI card BIOS to format the drive.

Dmitry Postrigan on August 20, 2007 3:02 pm Thanks Have you checked/replaced the cable? BUT ALL OTHER DRIVES DO!! have a peek at these guys Now that the drive was being detected (with its new partition), I attempted to run a few partition recovery tools.

When I enter setup (bios, whatever), I can change the boot sequence and press space to enable/disable drives as you say, but there are only three devices, floppy, cd-rom and hard stevesumner17-04-2006, 02:08 PMI just found this in another forum (http://www.neoseeker.com/Hardware/faqs/kb/15,24.html) "If you are running other ide hard drivers you will want to disable them in the bois first so that windows got a bsod and here we go! I certainly hope so… October 28, 2011 Dave The drives might very well still be good.

I did a ‘CTRL+A' and checked the properties in that drive which showed 12 GB is used (~18 free) but when I checked the properties on the drive it showed only Thank you so much! If they help in that way, I'm okay with it. So now I have to manually go into the bios (F12) and select the IDE drive to boot from.

What do I do now?