How To Slave A Sata Hard Drive In Windows 7
MSI Z87-GD65 Gaming MobO i5-4670K Haswell w/ Corsair H80i liquid cooling at 4.1 GHz @35C idle 16 GB Corsair Dominator Platinum at 1866 RAM Samsung EVO 500 GB SSD boot drive SATA-II drives usually have a jumper to make them SATA-I. Or that it only refuses to enter BIOS? by R. have a peek here
Jul 27, 2012 #4 (You must log in or sign up to reply here.) Show Ignored Content Similar Topics How to set up SATA HD as slave to a ATA master? Thanks for all your help! For some time now I have had a 500gb SATA drive on my ECS KV2 Lite, working alongside a 120gb IDE drive. The master / slave pertains only to the ide controller. http://www.techspot.com/community/topics/2-sata-as-master-slave-not-raid.41335/
How To Slave A Sata Hard Drive In Windows 7
Hope this helps. Discussion topics include SSD, SATA drives, USB drives, external hard drives, RAID arrays, backup, IDE drives, network attached storage (NAS), thumbdrives, Western Digital, Kingston, LaCie, and SanDisk.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General Firstly and most importantly, I am running Windows XP, not UBUNTU, but the problem seems to be so similar, I couldn't help but mention it.
Several functions may not work. But as I have said previously, the original hard drive has always been in IDE mode and worked fine. These HDDs may not evenbe detected at POST. How To Set A Hard Drive To Master As for master/slave...
I'm still hazy on this. Sata Hard Drive Slave Jumper Setting In one of my Hard drive, boot sector went bad. Same goes for SATA controllers.I think some SATA drives have legacy IDE plugs on them, but I'd only use the SATA plug with the small serial cable. Usually parts with a "Lite" designation have older chipsets, etc.
Upon starting the machine I get this message: VIA Technologies, inc.VIA VT8237 Serial ATA RAID BIOS Setting Utility V2.01 Scan devices, Please wait... Sata Hard Drive Jumper Settings There, the computer tells me that I have not enough disks for a raid config, but it does list the drive as Sata and tells me its size etc. I left it for an hour on ACPI, and nothing happened... I have a Gigabyte motherboard that will take 4 SATA drives, 2 PATA drives and 2 CD/DVD drives so I can use the PATA drives in a RAID Array as the
Sata Hard Drive Slave Jumper Setting
If I go into the RAID option and start to create a RAID array, it tells me that all data will be lost on the disks. http://www.overclockers.com/forums/showthread.php/301225-RAID-1-using-master-slave-drive-why-not Taken from manual** At least two SATA hard drives recommended that you use two hard drives with identical model and capacity. How To Slave A Sata Hard Drive In Windows 7 If you would like to check or change the SATA mode, please use Feature Tool provided by Hitachi. Master Slave Hard Drive Setup Ask a question and give support.
Enhanced mode device support must be set on to use a mixed device configuration. http://quodsoftware.com/hard-drive/how-to-connect-sata-hard-drive-to-motherboard.html Press
Jul 26, 2012 #3 Bharathwaj TS Rookie Topic Starter Thanks for your reply. Automotive ground shift phenomenon Why is generating 8 random bits uniform on (0, 255)? Don't know the technical details behind why the numbering scheme is the way it is, but it's nothing to worry about. Check This Out So I will not be able to boot boot into my computer using that hard drive.
foscooterMay 20, 2011, 10:07 AM No master/slave setting for SATA drives!You set up which is the boot drive in BIOS. Master Slave Hard Drive Jumper Settings The drive may be defective... Back again.
to continue! .
My first reply to your answer was kind of a brain fart. Flashing your BIOS should always be a last resort. Do you think that it should be set to raid for 2 sata hard drives to work ? How To Set Master Sata Drive Please refer to our CNET Forums policies for details.
Your mobo sounds similiar to mine. even though it has been authenticated? no, being 500GB is not an issue, the BIOS would just see less, if it was limited. http://quodsoftware.com/hard-drive/how-to-connect-ide-hard-drive-to-sata-motherboard.html There are no IDE port on Motherboard only SATA.
select boot sequence 4 insert winxp cd On my K8V SE deluxe there are 4 SATA connectors, SATA 1 and 2, SATA primary and sec. But before all hope is lost... Can I install my old Maxtor IDE drive without any conflicts or cable conflicts (even tho the later will have a flat cable)? [WindowsXP Prof, MSI MB K8N NEO4 Platinum mobo] Register now!
Prior settings of the jumpers to "slave" would result in no boot screen at all upon powering on. Will not give in !!!!!! Temporaly desativate secondary IDE Channel, while installing windows on HD SATA, because windows insist in write MBR both HD SATA and old IDE boot HD.4. The new sata hard drive is 500GB - I don't know if this is a problem.
the floppy drive....and i have no way of making a new floppy disc since i have no other pc with a floppy drive. If I go into the RAID option and start to create a RAID array, it tells me that all data will be lost on the disks. The single HD is now connected to SATA 1 (not my doing, I didn't build this) So the config I'm looking for should go to SATA primary and sec? Home Forum New Posts FAQ Calendar Community Groups Albums Member List Forum Rules & Guidelines Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Reviews News
There are some USB external floppy drives that XP can detect at boot but not many. Anyway, I don't really want RAID. I installed a Western Digital 200 gb SATA drive in a windows XP system and it only sees 100gb. Facebook Google+ Twitter YouTube Subscribe to TechSpot RSS Get our weekly newsletter Search TechSpot Trending Hardware The Web Culture Mobile Gaming Apple Microsoft Google Reviews Graphics Laptops Smartphones CPUs Storage Cases
At this point it should show up in windows with a new drive letter. Therefore most people can run 6 devices note that each sata connector MUST NOT be shared you may only connect 0 - 2 sata devices and 0 - 4 IDE devices.If Printing out the instructions and checking them off step by step is what I do, and I have been building/maintaining computers since 1978... You are not legally supposed to have any one copy of windows on more than one computer.
master and slave? Proffitt Forum moderator / July 20, 2005 8:19 AM PDT In reply to: I'll be wary 2. Try booting with just the potentially faulty drive, using a LiveCD. Not likely though, esp if you plugged the new drive into the same controller and it shows up.