ASUS A7N8X Del IDE Problem?
So for the heck of it I switched them, two hard drives on primary and the CD-RW on secondary and it booted through no problems! Top Starfalcon Gerbilus Supremus Posts: 11809 Joined: Mon Oct 14, 2002 10:43 am Location: Evergreen Park, IL Contact: Contact Starfalcon AOL Quote #29 Thu Aug 26, 2004 1:21 pm Did Edited by jpd9930, 22 September 2012 - 10:20 AM. again what do I look for to check this out?? his comment is here
his specs: A7N8X-E AMD XP-M 2500+ Maxtor 80 giga Older Maxtor 80 giga 1 gigabyte mushkin ram anyway, his would also cause problems. I'm guessing the new GART driver must have something to do with this. Maybe the GART driver update has something to do with SP2 compatibility. Hot Deals and Sponsor Specials Suggestions and Feedback « Previous Thread | Next Thread » Posting Permissions You may not post new threads You may not post replies You may not
even got some increase in IDE performance. I'll post more tomorrow after I have a chance to babysit with the install... If the power was bad, wouldn't it sometimes just cause problems? Two Hdd's in adjacent bays without an intake fan bringing in fresh air across them may be heating each other up intolerably.
In case its of any use this is a newly installed OS (SP2 slipstreamed) and the only nvidia drivers installed has been the 4.27 version which installed just fine. Or, If you have other stick/s of ram try them (after a CMOS clear). I'd always blamed it on a faulty driver or software install, (that's usually the only time I reboot) but now I wonder? RAID ... ", do you see: "Boot from CD: Press any key to boot from CD ..."and you will see one the dots appearing after CD, giving you 5 seconds to
I no longer receive that prompt during POST. Sep 12, 2005 #4 Captain_Jon TS Rookie Topic Starter Not a lot of replies to this one!! Reply With Quote 09-22-2004,12:27 AM #11 RickGr4 View Profile View Forum Posts Lost in Cyber Space Joined Apr 2001 Location Shoreview, MN Posts 853 Re: Nforce 5.10 install problems on A7N8X https://hardforum.com/threads/asus-a7n8x-e-problems-with-two-ide-drives-working-together.940210/ Abit BP6 2X [email protected] mhz, 1.5 GB PC133 ECC, Renditon Verite V2200, SB AWE32, Adaptec 2940U2W, 4.3GB Quantum Atlas 10K, Plextor Ultraplex Top Usacomp2k3 Gerbil God Posts: 21505 Joined: Thu
And enough old parts laying around to build at least two more rigs... Not sure. I assume at this point they had the drivers already loaded. Separate them by one bay's worth of space, or more.
Only file that loaded was si3112r.sys. https://technutopia.com/forum/showthread.php?t=6923 Now the bios show the line with my intern SATA before the lines with the extern SATA and I can see the extern SATA in Machine proporties - but not in There is also a problem with my two external LaCie SATA-drives which use a PCI-SCSI card. The more I read about Maxtor on the forums, the more I am convinced that these drives are the problem.
Reply With Quote 09-21-2004,05:18 AM #7 Razoola View Profile View Forum Posts Visit Homepage Registered User Joined Mar 2003 Posts 67 Re: Nforce 5.10 install problems on A7N8X Del v2. this content chicane, Aug 18, 2005 chicane, Aug 18, 2005 #9 Aug 21, 2005 #10 SomeFknGuy [H]ard|Gawd Messages: 1,097 Joined: Oct 13, 2003 where do i end up picking one of these converters? I do believe it is being reconized now. Windows installed no problem on the Seagate, got into Windows, and bam same problem.
nor do I know if it makes sense that a faulty power supply would cause the problems I am encountering. Not at the Raid prompt ...This concerns me! You should be running about 34-38c idle and about 40-48c load (typical for a K7 AMD rig with air cooling). weblink although my master drive is western digital 80 giga.
Thanks so far Back to top #4 AustrAlien AustrAlien Inquisitor BC Advisor 6,772 posts OFFLINE Gender:Male Location:Cowra NSW Australia Local time:05:41 AM Posted 11 September 2012 - 08:15 PM I'd Gold subscriber Administrator Posts: 46133 Joined: Tue Aug 20, 2002 10:51 pm Location: Somewhere, having a beer Quote #22 Wed Aug 25, 2004 6:14 pm If you hit Del earlier in You should then be fine.
However, when I press the eject button on my CD drive to replace the XP disk with a ME disk the *power turns off.
M Reply With Quote 09-23-2004,08:05 PM #13 RickGr4 View Profile View Forum Posts Lost in Cyber Space Joined Apr 2001 Location Shoreview, MN Posts 853 Some new light on the subject I just tried it just now and it got in! Sep 8, 2005 #3 Captain_Jon TS Rookie Topic Starter Clicking sounds from the HD also made me think that I had a problem with the hard drives... I switched the FSB to 133 and now it's reading an Athlon 2400+.
Since we don't reboot it that often, I foolishly didn't investigate further. I had not installed any other software and hadn't wasted much time as of yet, so I took a chance and installed the 5.10 drivers thinking I would format and reinstall The IDE driver locked my system and the GART driver would not install. check over here Should read FSB=133 (266DDR) and DRAM should be on "SPD" running at 133 (266DDR) also.
If not, I'll download new chipset drivers (though I doubt that's the problem unless they somehow got corrupted). Using the site is easy and fun. That's when things started getting weird. Thanks to everyone at bleeping for your [email protected] Jon Back to top BC AdBot (Login to Remove) BleepingComputer.com Register to remove ads #2 AustrAlien AustrAlien Inquisitor BC Advisor 6,772 posts
High end digitized ~ analog, turkey hunter. I have also tried multiple IDE cables, drive configurations(jumper wise) and what not...with 0 effect.... A bit rushed for time but I hope that this piece is of some interest. #4 RickyG, Aug 20, 2005 grooge Senior member Joined: Dec 23, 2004 Messages: 542 Likes Un-zip the downloaded file (right-click > Extract all) to extract the contents:You will find 2 folders and 8 files.Copy the 8 files ONLY (not the 2 folders) to a formatted floppy